| Paper | Title | Page |
|---|---|---|
| MOPEC078 | Commissioning of the Low Energy Beam Transport of the Front End Test Stand | 648 |
|
||
|
The Front End Test Stand (FETS) at the Rutherford Appleton Laboratory is intended to demonstrate the early stages of acceleration (0-3 MeV) and beam chopping required for high power proton accelerators, including proton drivers for pulsed neutron spallation sources and neutrino factories. A Low Energy Beam Transport (LEBT), consisting of three solenoids and four drift sections, is used to transport the H- beam from the ion source to the FETS Radio Frequency Quadrupole. We present the status of the installation and commissioning of the LEBT, and compare particle dynamics simulations with preliminary measurements of the H- beam transport through the LEBT. |
||
| MOPD056 | The Mechanical Engineering Design of the FETS RFQ | 810 |
|
||
|
This paper will present the mechanical engineering design for a 324 MHz 4-vane RFQ, which has been developed for the Front End Test Stand (FETS) project based at the Rutherford Appleton Laboratory (RAL) in the UK. The design criteria will be discussed along with particular design features of the RFQ including the tuners, vacuum ports, main body cooling pocket design and the support / alignment structure. Different techniques for creating the RF and vacuum seal between major and minor vanes are also discussed. |
||
| MOPD057 | Assessing the Transmission of the H- Ion Beam on the Front End Test Stand | 813 |
|
||
|
The front end test stand (FETS) [1] is entering the next stage of construction and commissioning, with the three-solenoid magnetic low energy beam transport (LEBT) line being installed. A thorough characterization of the beam leaving the Penning H- ion source has been performed. This includes measurements of the beam current using toroids and of the transverse emittance using slit-slit scanners. These measurements are performed over a wide range of source discharge and extraction parameters in order to understand how the transmission may be improved. Comments on the quality of the beam to be injected into the FETS radio frequency quadrupole (RFQ) are given. |
||
| MOPD058 | Combined Electromagnetic-Thermal-Structural Simulation of the Four-metre Radio Frequency Quadrupole to be Installed on the Front End Test Stand | 816 |
|
||
|
The front end test stand (FETS) [1] being constructed at the Rutherford Appleton Laboratory is entering the next stage of commissioning, with the three-solenoid magnetic low energy beam transport (LEBT) now installed and undergoing commissioning. The next major component to be manufactured is the 3 MeV, 324 MHz, four metre radio frequency quadrupole (RFQ). The mechanical design is almost complete so a comprehensive finite element model of the entire RFQ has been made in ANSYS to ensure the electromagnetic, thermal and structural properties are sound. An analysis of the cooling strategy and expected resonant frequency shift due to thermal expansion are presented. |
||
| MOPEC075 | Status of the RAL Front End Test Stand | 642 |
|
||
|
The Front End Test Stand (FETS) under construction at the Rutherford Appleton Laboratory is the UK's contribution to research into the next generation of High Power Proton Accelerators (HPPAs). HPPAs are an essential part of any future Spallation Neutron Source, Neutrino Factory, Muon Collider, Accelerator Driven Sub-critical System, Waste Transmuter etc. FETS will demonstrate a high quality, high intensity, chopped H-minus beam and is a collaboration between RAL, Imperial College and the Universtity of Warwick in the UK and the Universidad del Pais Vasco in Spain. This paper describes the current status and future plans of FETS. |
||
| THPEC070 | Pulse Lengthening Experiments on the FETS Ion Source | 4217 |
|
||
|
The Front End Test Stand (FETS) under construction at the Rutherford Appleton Laboratory is the UK's contribution to research into the next generation of High Power Proton Accelerators (HPPAs). Running at duty cycles of up 50 Hz with pulse lengths of 2 ms are required. This paper presents initial Hminus beam currents and emittance measurements for long pulse lengths. |
||
| THPEC068 | First Simulation Tests for the Bilbao Accelerator Ion Source Test Stand | 4211 |
|
||
|
The rationale behind the Bilbao Accelerator Ion Source Test Stand (ITUR) project is to perform a comparison between different kinds of hydrogen ion sources using the same beam diagnostics setup. In particular, a direct comparison will be made in terms of the emittance characteristics of Penning-type sources such as those currently being used in ISIS (UK) and those of microwave type such as CEA-Saclay and INFN. The aim here pursued is to build an Ion Source Test Stand where virtually any type of source can be tested and, thus, compared to the results of other sources under the same gauge. It would then be possible to establish a common ground for effectively comparing different ion sources. The work here presented reports on the first simulations for the H-/H+ extraction system, as well the devices that conform the diagnostic vessel: Faraday Cup, Pepperpot and Retarding Potential Analyzer (RPA), among others. |