ICALEPCS2015 - List of Authors (Magnin, N.)

Paper	Title	Page
MOPGF135	Upgrade of the Trigger Synchronisation and Distribution System of the Beam Dumping System of the Large Hadron Collider	397
	N. Magnin, A. Antoine, E. Carlier, V. Chareyre, S. Gabourin, A. Patsouli, N. Voumard CERN, Geneva, Switzerland
	Various upgrades were performed on the Large Hadron Collider (LHC) Beam Dumping System (LBDS) during Long Shutdown 1 (LS1) at CERN, in particular to the Trigger Synchronisation and Distribution System (TSDS): A redundant direct connection from the LHC Beam Interlock System to the re-trigger lines of the LBDS was implemented, a fully redundant powering architecture was set up, and new Trigger Synchronisation Unit cards were deployed over two separate crates instead of one. These hardware changes implied the adaptation of the State Control and Surveillance System and an improvement of the monitoring and diagnosis systems, like the various Internal Post Operation Check (IPOC) systems that ensure that, after every beam dump event, the LBDS worked as expected and is 'as good as new' for the next LHC beam. This paper summarises the changes performed on the TSDS during LS1, highlights the upgrade of the IPOC systems and presents the problems encountered during the commissioning of TSDS before the LHC Run II.
	Poster MOPGF135 [0.969 MB]
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPGF127	A Generic Timing Software for Fast Pulsed Magnet Systems at CERN	1003
	C. Chanavat, M. Arruat, E. Carlier, N. Magnin CERN, Geneva, Switzerland
	At CERN, fast pulsed magnet (kicker) systems are used to inject, extract, dump and excite beams. Depending on their operational functionalities and as a result of the evolution of controls solutions over time, the timing controls of these systems were based on hybrid hardware architectures that have resulted in a large disparity of software solutions. In order to cure this situation, a Kicker Timing Software (KiTS), based on a modular hardware and software architecture, has been developed with the objective to increase the homogeneity of fast and slow timings control for all types of fast pulsed magnet systems. The KiTS uses a hardware abstraction layer and a configurable software model implemented within the Front-End Software Architecture (FESA) framework. It has been successfully deployed in the control systems of the different types of kicker systems at CERN like for the PS continuous transfer, the SPS injection and extraction, the SPS tune measurement and the LHC injection.
	Poster WEPGF127 [38.304 MB]
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Upgrade of the Trigger Synchronisation and Distribution System of the Beam Dumping System of the Large Hadron Collider

397

N. Magnin, A. Antoine, E. Carlier, V. Chareyre, S. Gabourin, A. Patsouli, N. Voumard
CERN, Geneva, Switzerland

Various upgrades were performed on the Large Hadron Collider (LHC) Beam Dumping System (LBDS) during Long Shutdown 1 (LS1) at CERN, in particular to the Trigger Synchronisation and Distribution System (TSDS): A redundant direct connection from the LHC Beam Interlock System to the re-trigger lines of the LBDS was implemented, a fully redundant powering architecture was set up, and new Trigger Synchronisation Unit cards were deployed over two separate crates instead of one. These hardware changes implied the adaptation of the State Control and Surveillance System and an improvement of the monitoring and diagnosis systems, like the various Internal Post Operation Check (IPOC) systems that ensure that, after every beam dump event, the LBDS worked as expected and is 'as good as new' for the next LHC beam. This paper summarises the changes performed on the TSDS during LS1, highlights the upgrade of the IPOC systems and presents the problems encountered during the commissioning of TSDS before the LHC Run II.

Poster MOPGF135 [0.969 MB]

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPGF127

A Generic Timing Software for Fast Pulsed Magnet Systems at CERN

1003

C. Chanavat, M. Arruat, E. Carlier, N. Magnin
CERN, Geneva, Switzerland

At CERN, fast pulsed magnet (kicker) systems are used to inject, extract, dump and excite beams. Depending on their operational functionalities and as a result of the evolution of controls solutions over time, the timing controls of these systems were based on hybrid hardware architectures that have resulted in a large disparity of software solutions. In order to cure this situation, a Kicker Timing Software (KiTS), based on a modular hardware and software architecture, has been developed with the objective to increase the homogeneity of fast and slow timings control for all types of fast pulsed magnet systems. The KiTS uses a hardware abstraction layer and a configurable software model implemented within the Front-End Software Architecture (FESA) framework. It has been successfully deployed in the control systems of the different types of kicker systems at CERN like for the PS continuous transfer, the SPS injection and extraction, the SPS tune measurement and the LHC injection.

Poster WEPGF127 [38.304 MB]

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)