IBIC2012 - List of Authors (Soby, L.)

Paper	Title	Page
MOPA16	Design and Characterization of a Prototype Stripline Beam Position Monitor for the CLIC Drive Beam	87
	A. Benot-Morell, L. Søby, M. Wendt CERN, Geneva, Switzerland A. Benot-Morell IFIC, Valencia, Spain J.M. Nappa, J. Tassan-Viol, S. Vilalte IN2P3-LAPP, Annecy-le-Vieux, France S.R. Smith SLAC, Menlo Park, California, USA
	Funding: FPA2010-21456-C02-01, SEIC-2010-00028 The prototype of a stripline Beam Position Monitor (BPM) with its associated readout electronics is under development at CERN, in collaboration with SLAC, LAPP and IFIC. The anticipated position resolution and accuracy are expected to be below 2μm and 20μm respectively for operation of the BPM in the CLIC drive beam (DB) linac. This paper describes the particular CLIC DB conditions with respect to the beam position monitoring, presents the measurement concept, and summarizes electromagnetic simulations and RF measurements performed on the prototype.

MOPA18	A Prototype Cavity Beam Position Monitor for the CLIC Main Beam	95
	F.J. Cullinan, S.T. Boogert, N.Y. Joshi, A. Lyapin JAI, Egham, Surrey, United Kingdom D. Bastard, E. Calvo, N. Chritin, F. Guillot-Vignot, T. Lefèvre, L. Søby, M. Wendt CERN, Geneva, Switzerland A. Lunin, V.P. Yakovlev Fermilab, Batavia, USA S.R. Smith SLAC, Menlo Park, California, USA
	The Compact Linear Collider (CLIC) places unprecedented demands on its diagnostics systems. A large number of cavity beam position monitors (BPMs) throughout the main linac and beam delivery system must routinely perform with 50 nm spatial resolution. Multiple position measurements within a single 156~ns bunch train are also required. A prototype low-Q cavity beam position monitor has been designed and built to be tested on the CLIC Test Facility (CTF3) probe beam. This paper presents the latest measurements of the prototype cavity BPM and the design and simulation of the radio frequency (RF) signal processing electronics with regards to the final performance. Installation of the BPM in the CTF3 probe beamline is also discussed.

Paper

Title

Page

Design and Characterization of a Prototype Stripline Beam Position Monitor for the CLIC Drive Beam

87

A. Benot-Morell, L. Søby, M. Wendt
CERN, Geneva, Switzerland
A. Benot-Morell
IFIC, Valencia, Spain
J.M. Nappa, J. Tassan-Viol, S. Vilalte
IN2P3-LAPP, Annecy-le-Vieux, France
S.R. Smith
SLAC, Menlo Park, California, USA

Funding: FPA2010-21456-C02-01, SEIC-2010-00028
The prototype of a stripline Beam Position Monitor (BPM) with its associated readout electronics is under development at CERN, in collaboration with SLAC, LAPP and IFIC. The anticipated position resolution and accuracy are expected to be below 2μm and 20μm respectively for operation of the BPM in the CLIC drive beam (DB) linac. This paper describes the particular CLIC DB conditions with respect to the beam position monitoring, presents the measurement concept, and summarizes electromagnetic simulations and RF measurements performed on the prototype.

MOPA18

A Prototype Cavity Beam Position Monitor for the CLIC Main Beam

95

F.J. Cullinan, S.T. Boogert, N.Y. Joshi, A. Lyapin
JAI, Egham, Surrey, United Kingdom
D. Bastard, E. Calvo, N. Chritin, F. Guillot-Vignot, T. Lefèvre, L. Søby, M. Wendt
CERN, Geneva, Switzerland
A. Lunin, V.P. Yakovlev
Fermilab, Batavia, USA
S.R. Smith
SLAC, Menlo Park, California, USA

The Compact Linear Collider (CLIC) places unprecedented demands on its diagnostics systems. A large number of cavity beam position monitors (BPMs) throughout the main linac and beam delivery system must routinely perform with 50 nm spatial resolution. Multiple position measurements within a single 156~ns bunch train are also required. A prototype low-Q cavity beam position monitor has been designed and built to be tested on the CLIC Test Facility (CTF3) probe beam. This paper presents the latest measurements of the prototype cavity BPM and the design and simulation of the radio frequency (RF) signal processing electronics with regards to the final performance. Installation of the BPM in the CTF3 probe beamline is also discussed.