EPAC 2004 - List of Authors

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Teytelman, D.

Paper	Title	Page
MOPLT144	Design for a 10³⁶ Super-B-factory at PEP-II	878
	J. Seeman, Y. Cai, F.-J. Decker, S. Ecklund, A.S. Fisher, J.D. Fox, S.A. Heifets, A. Novokhatski, M.K. Sullivan, D. Teytelman, U. Wienands SLAC, Menlo Park, California
	Design studies are underway to arrive at a complete parameter set for a very high luminosity e⁺e^- Super B-Factory (SBF) in the luminosity range approaching 10³⁶/cm²/s. The design is based on a collider in the PEP-II tunnel but with an upgraded RF system (higher frequency), magnets, vacuum system, and interaction region. The accelerator physics issues associated with this design are reviewed as well as the site and power constraints. Near term future studies will be discussed.
TUPKF062	PEP-II RF System Operation and Performance	1087
	P.A. McIntosh, J. Browne, J.E. Dusatko, J.D. Fox, W.C. Ross, D. Teytelman, D. Van Winkle SLAC, Menlo Park, California
	The Low Energy Ring (LER) and High Energy Ring (HER) RF systems have operated now on PEP-II since July 1998 and have assisted in breaking all design luminosity records back in June 2002. Luminosity on PEP-II has steadily increased since then as a consequence of larger e⁺ and e^- beam currents being accumulated. This has meant that the RF systems have inevitably been driven harder, not only to achieve these higher stored beam currents, but also to reliably keep the beams circulating whilst at the same time minimizing the number of aborts due to RF system faults. This paper details the current PEP-II RF system configurations for both rings, as well as future upgrade plans spanning the next 3-5 years. Limitations of the current RF system configurations are presented, highlighting improvement projects which will target specific areas within the RF systems to ensure that adequate operating overheads are maintained and reliable operation is assured.
THPLT155	Development and Testing of a Low Group-delay Woofer Channel for PEP-II	2819
	J.D. Fox, L. Beckman, D. Teytelman, D. Van Winkle, A. Young SLAC, Menlo Park, California
	The PEP-II HER and LER require active longitudinal feedback to control coupled-bunch instabilities. The PEP-II RF systems use direct and comb loop feedback to reduce the cavity fundamental impedance, though the remaining low-mode impedance is providing the fastest growing unstable modes in both rings. Since commissioning the longitudinal feedback systems have used a dedicated "woofer" channel to apply the low-frequency correction kick via the RF system. The performance of this original controller is limited by the maximum gain that can be supported due to the processing delay (group delay), as well as the difficulty in configuring a common correction controller that acts via two correction paths. A dedicated low-mode signal processing system has been developed to allow higher damping rates. It is a digital processing channel, operating at a 10 MHz sampling rate, and implementing flexible 5 to 10 tap FIR control filters. The design of the channel and initial control filters is presented, as are initial machine experiments quantifying the damping and noise floor of this low group delay woofer system.
THPLT160	Measurements of Transverse Coupled-bunch Instabilities in PEP-II	2831
	D. Teytelman, R. Akre, J.D. Fox, S.A. Heifets, A. Krasnykh, D. Van Winkle, U. Wienands SLAC, Menlo Park, California
	At the design currents the PEP-II High and Low Energy Rings operate above the coupled-bunch instability thresholds in horizontal and vertical planes. Both machines have used analog bunch-by-bunch feedback systems to stabilize the beams since commissioning. Here we present a measurement technique that uses the capabilities of the PEP-II programmable digital longitudinal feedback system to provide transient diagnostics in X or Y directions. This technique allows one to measure instability growth or damping rates as well as oscillation frequencies in both open-loop and closed-loop conditions. Based on these measurements the configuration of the relevant transverse feedback channel can be optimized. The technique will be illustrated with instability measurements and feedback optimization examples. Comparisons of the measured modal patterns and growth rates to the theoretical predictions will be presented.
MOPLT143	Results and Plans of the PEP-II B-Factory	875
	J. Seeman, J. Browne, Y. Cai, S. Colocho, F.-J. Decker, M.H. Donald, S. Ecklund, R.A. Erickson, A.S. Fisher, J.D. Fox, S.A. Heifets, R.H. Iverson, A. Kulikov, A. Novokhatski, M.T.F. Pivi, M.C. Ross, P. Schuh, T.J. Smith, K. Sonnad, M. Stanek, M.K. Sullivan, P. Tenenbaum, D. Teytelman, J.L. Turner, D. Van Winkle, U. Wienands, M. Woodley, Y.T. Yan, G. Yocky SLAC, Menlo Park, California M.E. Biagini INFN/LNF, Frascati (Roma) J.N. Corlett, C. Steier, A. Wolski, M.S. Zisman LBNL, Berkeley, California W. Kozanecki CEA/DSM/DAPNIA, Gif-sur-Yvette G. Wormser IPN, Orsay
	PEP-II is an e⁺e^- B-Factory Collider located at SLAC operating at the Upsilon 4S resonance. PEP-II has delivered, over the past four years, an integrated luminosity to the BaBar detector of over 175 fb-1 and has reached a luminosity over 7.4x10³³/cm²/s. Steady progress is being made in reaching higher luminosity. The goal over the next few years is to reach a luminosity of at least 2x10³⁴/cm²/s. The accelerator physics issues being addressed in PEP-II to reach this goal include the electron cloud instability, beam-beam effects, parasitic beam-beam effects, trickle injection, high RF beam loading, lower beta y*, interaction region operation, and coupling control.