IPAC2011 - List of Authors (Lyapin, A.)

Paper	Title	Page
MOPC049	Bead-pull Test Bench for Studying Accelerating Structures at RHUL	187
	S. Molloy ESS, Lund, Sweden R. Ainsworth, G.E. Boorman Royal Holloway, University of London, Surrey, United Kingdom C. Gabor STFC/RAL/ASTeC, Chilton, Didcot, Oxon, United Kingdom A. Garbayo AVS, Eibar, Gipuzkoa, Spain A.P. Letchford STFC/RAL, Chilton, Didcot, Oxon, United Kingdom A. Lyapin JAI, Egham, Surrey, United Kingdom P. Savage Imperial College of Science and Technology, Department of Physics, London, United Kingdom
	A bead-pull test stand has been constructed at Royal Holloway, University of London (RHUL) with the ability to provide electric field profile measurements along five degrees of freedom using the perturbation method. In this paper, we present example measurements using the test bench which include a field flatness profile of a 324MHz four vane Radio Frequency Quadrupole (RFQ) model designed as part of the Front End Test Stand (FETS) development at Rutherford Appleton Laboratory (RAL). Mechanical and operational details of the apparatus will also be described, as well as future plans for the development and usage of this facility.

TUPC025	Calibration Errors in the Cavity Beam Position Monitor System at the ATF2	1051
	F.J. Cullinan, S.T. Boogert, N.Y. Joshi, A. Lyapin JAI, Egham, Surrey, United Kingdom
	It has been shown at the Accelerator Test Facility at KEK, that it is possible to run a system of 37 cavity beam position monitors (BPMs) and achieve high working resolution. However, stability of the calibration constants (position scale and radio frequency (RF) phase) over a three/four week running period is yet to be demonstrated. During the calibration procedure, random beam jitter gives rise to a statistical error in the position scale and slow orbit drift in position and tilt causes systematic errors in both the position scale and RF phase. These errors are dominant and have been evaluated for each BPM. The results are compared with the errors expected after a tested method of beam jitter subtraction has been applied.

TUPC164	Position Determination of Closely Spaced Bunches using Cavity BPMs	1419
	N.Y. Joshi, S.T. Boogert, F.J. Cullinan, A. Lyapin JAI, Egham, Surrey, United Kingdom
	Cavity Beam Position Monitor (BPM) systems with high-Q form a major part of precision position measurement diagnostics for linear accelerators with low emittance beam. Using cavity BPMs, the position resolution of less than 100 nm has been demonstrated in single bunch mode operation. In the case of closely spaced bunches, where the decay time of the cavity is comparable to the time separation between bunches, the BPM signal from a bunch is polluted by the signal induced from the previous bunches in the same bunch-train. This paper discuss our ongoing work to develop the methods to extract the position of the closely spaced bunches using cavity BPMs. A signal subtraction code is being developed to remove the signal pollution from previous bunches and to determine the individual bunch position. Another code has been developed to simulate the BPM data for the cross check. Performance of the code is studied on the experimental and simulated data. Application of the analysis techniques to the linear colliders, such as International Linear Collider (ILC) and Compact LInear Collider (CLIC), are briefly discussed.

TUPC161	Cavity Beam Position Monitor System for ATF2	1410
	S.T. Boogert, R. Ainsworth, G.E. Boorman, S. Molloy Royal Holloway, University of London, Surrey, United Kingdom A.S. Aryshev, Y. Honda, N. Terunuma, J. Urakawa KEK, Ibaraki, Japan F.J. Cullinan, N.Y. Joshi, A. Lyapin JAI, Egham, Surrey, United Kingdom J.C. Frisch, D.J. McCormick, J. Nelson, T.J. Smith, G.R. White SLAC, Menlo Park, California, USA A. Heo, E.-S. Kim, Y.I. Kim KNU, Deagu, Republic of Korea
	The Accelerator Test Facility 2 (ATF2) in KEK, Japan, is a prototype scaled demonstrator system for the final focus required for a future high energy lepton linear collider. The ATF2 beam-line is instrumented with a total of 41 high resolution C and S band resonant cavity beam position monitors (BPM) with associated mixer electronics and digitizers. In addition 4 high resolution BPMs have been recently installed at the interaction point, we briefly describe the first operational experience of these cavities in the ATF2 beam-line. The current status of the overall BPM system is also described, with a focus on operational techniques and performance.

Paper

Title

Page

Bead-pull Test Bench for Studying Accelerating Structures at RHUL

187

S. Molloy
ESS, Lund, Sweden
R. Ainsworth, G.E. Boorman
Royal Holloway, University of London, Surrey, United Kingdom
C. Gabor
STFC/RAL/ASTeC, Chilton, Didcot, Oxon, United Kingdom
A. Garbayo
AVS, Eibar, Gipuzkoa, Spain
A.P. Letchford
STFC/RAL, Chilton, Didcot, Oxon, United Kingdom
A. Lyapin
JAI, Egham, Surrey, United Kingdom
P. Savage
Imperial College of Science and Technology, Department of Physics, London, United Kingdom

A bead-pull test stand has been constructed at Royal Holloway, University of London (RHUL) with the ability to provide electric field profile measurements along five degrees of freedom using the perturbation method. In this paper, we present example measurements using the test bench which include a field flatness profile of a 324MHz four vane Radio Frequency Quadrupole (RFQ) model designed as part of the Front End Test Stand (FETS) development at Rutherford Appleton Laboratory (RAL). Mechanical and operational details of the apparatus will also be described, as well as future plans for the development and usage of this facility.

TUPC025

Calibration Errors in the Cavity Beam Position Monitor System at the ATF2

1051

F.J. Cullinan, S.T. Boogert, N.Y. Joshi, A. Lyapin
JAI, Egham, Surrey, United Kingdom

It has been shown at the Accelerator Test Facility at KEK, that it is possible to run a system of 37 cavity beam position monitors (BPMs) and achieve high working resolution. However, stability of the calibration constants (position scale and radio frequency (RF) phase) over a three/four week running period is yet to be demonstrated. During the calibration procedure, random beam jitter gives rise to a statistical error in the position scale and slow orbit drift in position and tilt causes systematic errors in both the position scale and RF phase. These errors are dominant and have been evaluated for each BPM. The results are compared with the errors expected after a tested method of beam jitter subtraction has been applied.

TUPC164

Position Determination of Closely Spaced Bunches using Cavity BPMs

1419

N.Y. Joshi, S.T. Boogert, F.J. Cullinan, A. Lyapin
JAI, Egham, Surrey, United Kingdom

Cavity Beam Position Monitor (BPM) systems with high-Q form a major part of precision position measurement diagnostics for linear accelerators with low emittance beam. Using cavity BPMs, the position resolution of less than 100 nm has been demonstrated in single bunch mode operation. In the case of closely spaced bunches, where the decay time of the cavity is comparable to the time separation between bunches, the BPM signal from a bunch is polluted by the signal induced from the previous bunches in the same bunch-train. This paper discuss our ongoing work to develop the methods to extract the position of the closely spaced bunches using cavity BPMs. A signal subtraction code is being developed to remove the signal pollution from previous bunches and to determine the individual bunch position. Another code has been developed to simulate the BPM data for the cross check. Performance of the code is studied on the experimental and simulated data. Application of the analysis techniques to the linear colliders, such as International Linear Collider (ILC) and Compact LInear Collider (CLIC), are briefly discussed.

TUPC161

Cavity Beam Position Monitor System for ATF2

1410

S.T. Boogert, R. Ainsworth, G.E. Boorman, S. Molloy
Royal Holloway, University of London, Surrey, United Kingdom
A.S. Aryshev, Y. Honda, N. Terunuma, J. Urakawa
KEK, Ibaraki, Japan
F.J. Cullinan, N.Y. Joshi, A. Lyapin
JAI, Egham, Surrey, United Kingdom
J.C. Frisch, D.J. McCormick, J. Nelson, T.J. Smith, G.R. White
SLAC, Menlo Park, California, USA
A. Heo, E.-S. Kim, Y.I. Kim
KNU, Deagu, Republic of Korea

The Accelerator Test Facility 2 (ATF2) in KEK, Japan, is a prototype scaled demonstrator system for the final focus required for a future high energy lepton linear collider. The ATF2 beam-line is instrumented with a total of 41 high resolution C and S band resonant cavity beam position monitors (BPM) with associated mixer electronics and digitizers. In addition 4 high resolution BPMs have been recently installed at the interaction point, we briefly describe the first operational experience of these cavities in the ATF2 beam-line. The current status of the overall BPM system is also described, with a focus on operational techniques and performance.