A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z  

Yu, M.

Paper Title Page
MOPEB051 Design of Helical Solenoid Combined with RF Cavity 382
 
  • V.S. Kashikhin, N. Andreev, V. Kashikhin, M.J. Lamm, A.V. Makarov, G.V. Romanov, K. Yonehara, M. Yu, A.V. Zlobin
    Fermilab, Batavia
 
 

Helical Solenoids (HS) were proposed for a muon beam ionization cooling. There are substantial up to 30 MeV/m energy losses during passing the muon beam through an absorber. The main issue of such system is the energy recovery. A conventional RF cavity has diameter which is too large to be placed inside HS. In the paper presented results of dielectric filled RF cavity design. The proposed cavity has helical configuration. Presented Helical Cooling Channel module design which includes: high pressure vessel, RF cavity, and superconducting HS. Discussed parameters of this module sub-systems and shown results of muon beam tracking in combined magnetic and electric 3D fields.

 
MOPEB054 Modeling the High-Field Section of a Muon Helical Cooling Channel 391
 
  • A.V. Zlobin, E.Z. Barzi, V.S. Kashikhin, M.J. Lamm, V. Lombardo, M.L. Lopes, M. Yu
    Fermilab, Batavia
  • G. Flanagan, R.P. Johnson, S.A. Kahn, M. Turenne
    Muons, Inc, Batavia
 
 

The Helical Cooling Channel (HCC) is a technique proposed for six-dimensional (6D) cooling of muon beams. The HCC for muon collider and some other applications is usually divided into several sections each with progressively stronger fields, smaller aperture, and shorter helix period to achieve the optimal muon cooling rate. Novel magnet design concepts based on simple coils arranged in a helical solenoid configuration have been developed to provide HCC magnet systems with the desired parameters. The level of magnetic field in the HCC high-field sections suggests using a hybrid coil structure with High Temperature Superconductors (HTS) in the innermost coil layers and Nb3Sn superconductor in the outer coil layers. The development of the concepts and engineering designs of hybrid helical solenoids based on advanced superconductor technologies, with special emphasis on the use of HTS for high fields at low temperature is the key step towards a practical HCC. This paper describes the conceptual designs and parameters of a short HTS model of a hybrid helical solenoid, and discusses the structural materials choices, fabrication techniques, and first test results.

 
WEPE072 Incorporating RF into a Muon Helical Cooling Channel 3509
 
  • S.A. Kahn, G. Flanagan, R.P. Johnson, M.L. Neubauer
    Muons, Inc, Batavia
  • V.S. Kashikhin, M.L. Lopes, K. Yonehara, M. Yu, A.V. Zlobin
    Fermilab, Batavia
 
 

A helical cooling channel (HCC) consisting of a pressurized gas absorber imbedded in a magnetic channel that provides solenoidal, helical dipole and helical quadrupole fields has shown considerable promise in providing six-dimensional cooling for muon beams. The energy lost by muons traversing the gas absorber needs to be replaced by inserting RF cavities into the HCC lattice. Replacing the substantial muon energy losses using RF cavities with reasonable gradients will require a significant fraction of the channel length be devoted to RF. However to provide the maximum phase space cooling and minimum muon losses, the HCC should have a short period and length. In this paper we examine an approach where each HCC cell has an RF cavity imbedded in the aperture with the magnetic coils are split allowing for half of the cell length to be available for the RF coupler and other services.