JAI, Oxford
Royal Holloway, University of London, Surrey
KEK, Ibaraki
SLAC, Menlo Park, California
Kyungpook National University, Daegu
UCL, London
KNU, Deagu
Fermilab, Batavia
PLS, Pohang
The Accelerator Test Facility 2 (ATF2) in KEK, Japan, is a prototype scaled demonstrator system for the final focus required for a lepton linear collider. The ATF2 beam-line is instrumented with a total of 38 C and S band resonant cavity beam position monitors (BPM) with associated mixer electronics and digitizers. The current status of the BPM system is described, with a focus on operational techniques and performance.
SLAC, Menlo Park, California
LBNL, Berkeley, California
EPFL, Lausanne
In this paper we describe the technical design of an on-going proof-of-principle echo-enabled harmonic generation (EEHG) FEL experiment in the Next Linear Collider Test Accelerator (NLCTA) at SLAC. The experiment was designed through late 2009 and built and installed between October 2009 and January 2010. We present the design considerations, the technical realization and the expected performances of the EEHG experiment.
SLAC, Menlo Park, California
LBNL, Berkeley, California
EPFL, Lausanne
ECHO-7 is a proof-of-principle echo-enabled harmonic generation* FEL experiment in the Next Linear Collider Test Accelerator (NLCTA) at SLAC. The experiment aims to generate coherent radiation at 318 nm and 227 nm, which is the 5th and 7th harmonic of the infrared seed laser. In this paper we present the preliminary results from the commissioning run of the completed experimental setup which started in April 2010.
* G. Stupakov, PRL, 102, 074801 (2009); D. Xiang and G. Stupakov, PRST-AB, 12, 030702 (2009).
SLAC, Menlo Park, California
IHEP Beijing, Beijing
LAL, Orsay
IN2P3-LAPP, Annecy-le-Vieux
ICEPP, Tokyo
University of Tokyo, Tokyo
KEK, Ibaraki
CERN, Geneva
The primary aim of the ATF2 research accelerator is to test a scaled version of the final focus optics planned for use in next-generation linear lepton colliders. ATF2 consists of a 1.3 GeV linac, damping ring providing low-emittance electron beams (<12pm in the vertical plane), extraction line and final focus optics. The design details of the final focus optics and implementation at ATF2 are presented elsewhere* . The ATF2 accelerator is currently being commissioned, with a staged approach to achieving the design IP spot size. It is expected that as we implement more demanding optics and reduce the vertical beta function at the IP, the tuning becomes more difficult and takes longer. We present here a description of the implementation of the overall tuning algorithm and describe operational experiences and performances
* Beam-Based Alignment, Tuning and Beam Dynamics Studies for the ATF2 Extraction Line and Final Focus System. Glen R. White , S. Molloy, M. Woodley, (SLAC). EPAC08-MOPP039, SLAC-PUB-13303.
SLAC, Menlo Park, California
Linac Energy Management (LEM) is a control system program which calculates, and optionally implements, magnet setpoint settings (BDESs) following a change in Energy (such as a change in the number, phase, and amplitude of active klystrons). The change is made relative to those magnets' existing BDES setpoints by a factor encoding the change in energy. LEM is necessary because changes in the number, phase, and amplitude of the active klystrons (the so-called "Klystron complement") change the beam's rigidity, and therefore, to maintain constant optics, one has to change focusing gradients and bend fields. This paper describes the basic process and some of the implementation lessons learned for LEM at the LCLS.
LAL, Orsay
KEK, Ibaraki
SLAC, Menlo Park, California
The purpose of ATF2 is to deliver a beam with stable very small spotsizes as required for future linear colliders such as ILC or CLIC. To achieve that, precise controls of the aberrations such as dispersion and coupling are necessary. Theoretically, the complete reconstruction of the beam matrix is possible from the measurements of horizontal, vertical and tilted beam sizes, combining skew quadrupole scans at several wire-scanner positions. Such measurements were performed in the extraction line of ATF2 in May 2009. We present analysis results attempting to resolve the 4X4 beam matrix and discuss the experimental limitations of 4D emittance measurements with wire scanners.
CERN, Geneva
LAL, Orsay
KEK, Ibaraki
BNL, Upton, Long Island, New York
SLAC, Menlo Park, California
The current ATF2 Ultra-Low beta proposal was designed to achieve 20nm vertical IP beam size without considering the multipolar components of the FD magnets. In this paper we describe different scenarios that avoid the detrimental effect of these multipolar errors in the FD. The simplest approach consists in modifying the optics but other solutions are studied as the introduction of new higher order magnets or the replacement of the FD with SC technology. The practical aspects of such an upgrade are the tuning performance and the compatibility with existing devices and instrumentation. These are fully addressed in the paper.