• P.C. Chiu, J. Chen, Y.K. Chen, Y.-S. Cheng, K.T. Hsu, K.H. Hu, C.H. Kuo
  NSRRC, Hsinchu

To keep and achieve desired performance of a modern synchrotron light source, it requires continuous efforts including good design of the accelerator, good performed subsystems and sophisticated feedback system. While some wonders happen unexpectedly and could deteriorate performance of the light source. For examples, some strong source occasionally occurred especially after long shut down or malfunction of some corrector power supply and it would result in increased noise level. Non ideal injection element will cause large perturbation as well. This report presents algorithms to spatially locate source and summarize some of our practical experience to identify the source.

• Y.K. Chen, J. Chen, Y.-S. Cheng, P.C. Chiu, K.T. Hsu, K.H. Hu, C.H. Kuo, C.Y. Wu
  NSRRC, Hsinchu

Modbus-TCP is a widely used in industry for a long time and accelerator control system recently. Modbus protocol over Ethernet has advantages for non real-time applications due to its maturity. The TPS (Taiwan Photon Source) project will have many Modbus-TCP enable devices which distributed in utility system and accelerator system. The accelerator control environment of TPS project is an EPICS toolkit based system. Modbus-TCP might adopt for some subsystems. There are several possible Modbus-TCP devices including the prototype power supply for magnet field mapping application equip with Modbus-TCP interface, vacuum system local controller, front-end controller, and some monitoring devices. In this paper, we will summarise preparation efforts to accommodate the Modbus-TCP support in the TPS control system.

• Y.-S. Cheng, J. Chen, Y.K. Chen, K.T. Hsu, K.H. Hu, C.H. Kuo, C.Y. Wu
  NSRRC, Hsinchu

To enhance waveform and spectrum remote access supports in the Taiwan Light Source (TLS), development of the EPICS support of Ethernet-based oscilloscope and spectrum analyzer for the TLS is under way. The EPICS platforms which built to interface these instruments could access the waveform and spectrum through the PV (Process Variable) channel access. By using remote operations of waveform and spectrum acquisition, long distance cabling could be eliminated and signal quality be improved. The EDM (Extensible Display Manager) tool is used to implement the operation interface of control console and provide waveform display. According to specific purpose use, different graphical user interfaces to integrate waveform and spectrum acquisition are built. This project is the preparation for future control room integration with the Taiwan Photon Source control room. The efforts will be described at this report.

• K.T. Hsu, Y.-T. Chang, J. Chen, Y.K. Chen, Y.-S. Cheng, P.C. Chiu, S.Y. Hsu, K.H. Hu, C.H. Kuo, D. Lee, Y.R. Pan, C.-J. Wang, C.Y. Wu
  NSRRC, Hsinchu

Implementation of the Control system for the Taiwan Photon Source (TPS) is on going. The TPS control system will provide versatile environments for machine commissioning, operation, and to do accelerator experiments. The control system is based on EPICS toolkits. Test-bed has set up for various developments. The open architecture will facilitate machine upgrade, modification easily and minimize efforts for machine maintenance. Performance and reliability of the control system will be guaranteed from the design phase. Development status will be summary in this report.

• P.C. Chiu, J. Chen, Y.K. Chen, Y.-S. Cheng, K.T. Hsu, C.H. Kuo, C.Y. Wu
  NSRRC, Hsinchu

In order to help early development of TPS control system and user interface, a virtual accelerator model is constructed. The virtual accelerator has been created by AT toolbox and simulated beam behavior; the Middle Layer providing high level accelerator application is also used. LabCA interfaces between Matlab and EPICS (Experimental Physics and Industrial Control System). Such a system could speed development of commissioning required software and examine the correction of all procedures.

• C.Y. Wu, J. Chen, Y.-S. Cheng, C.-S. Fann, K.T. Hsu, S.Y. Hsu, K.H. Hu, C.H. Kuo, D. Lee, K.-K. Lin
  NSRRC, Hsinchu
• K. Furukawa, J.-I. Odagiri
  KEK, Ibaraki

The EPICS embedded programmable logic controller (PLC) has been developed based on F3RP61-2L, a CPU module of a FA-M3R series PLC running Linux OS. The EPICS IOC resided in F3RP61-2L module can access the registers of sequence CPU modules and I/O modules of the PLC. The embedded EPICS PLC was applied to control the prototype of pulse magnet power supply and support functionality testing remotely. The system comprises various input/output modules and a CPU module with built-in Ethernet interface. The control information (status of the power supply, ON, OFF, warn up, reset, read/write voltage, etc.) can be accessed remotely using EPICS client tools. The EDM is selected to develop the GUI for itself. Efforts are summarized in this report.

• C.H. Kuo, J. Chen, P.C. Chiu, K.T. Hsu, K.H. Hu
  NSRRC, Hsinchu

As the latest generation light source, TPS (Taiwan Photon Source) has stringent requirements to perform submicron beam stability with low emittance. The slow and fast correctors of integrated orbit feedback system have been designed for TPS project, therefore some feedback system designed based on them an operation experiences from TLS. This report will present performance simulation and the initial design of system infrastructure for large scale calculation and wide bandwidth communication. To perform this requirement, FPGA-based platform will be implemented to achieve low latency and fast computation. Some studies of integrated feedback loop, communication structure, devices control such as BPM electronics and corrector power supplies are also described.