A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z  

Henry, J.

Paper Title Page
WEPEC076 Recent Progress on High-Current SRF Cavities at JLab 3052
 
  • R.A. Rimmer, W.A. Clemens, J. Henry, P. Kneisel, K. Macha, F. Marhauser, L. Turlington, H. Wang
    JLAB, Newport News, Virginia
 
 

JLab has designed and fabricated several prototype SRF cavities with cell shapes optimized for high current beams and with strong damping of unwanted higher order modes. We report on the latest test results of these cavities and on developments of concepts for new variants optimized for particular applications such as light sources and high-power proton accelerators, including betas less than one. We also report on progress towards a first beam test of this design in the recirculation loop of the JLab ERL based FEL. With growing interest worldwide in applications of SRF for high-average power electron and hadron machines, a practical test of these concepts is highly desirable. We plan to package two prototype cavities in a de-mountable cryomodule for temporary installation into the JLab FEL for testing with RF and beam. This will allow verification of all critical design and operational parameters paving the way to a full-scale prototype cryomodule.

 
WEPEC079 Design and Prototype Progress toward a Superconducting Crab Cavity Cryomodule for the APS 3061
 
  • H. Wang, G. Cheng, G. Ciovati, J. Henry, P. Kneisel, R.A. Rimmer, G. Slack, L. Turlington
    JLAB, Newport News, Virginia
  • R. Nassiri, G.J. Waldschmidt
    ANL, Argonne
 
 

A squashed, elliptical supercondconducting (SC) cavity with waveguide dampers on the beam pipes has currently been chosen as the baseline design [1] for the Short Pulse X-ray (SPX) project at the Advanced Photon Source (APS). An alternate cavity design, with a waveguide damper located directly on the cavity cell for improved damping characteristics, has also been designed and cold-tested with promising results. In either case, eight cavities would be operated CW in a single cryomodule at 2K to produce an electron bunch chirp of 4MV at a frequency of 2.815 GHz. Detailed analysis of multipactoring (MP), lorentz force detuning (LFD), and the thermal properties of the baseline design has led to an engineering specification of the basic parameters of the cryomodule.

 
THPEA057 Development of a CW NCRF Photoinjector using Solid Freeform Fabrication (SFF) 3804
 
  • P. Frigola, R.B. Agustsson, L. Faillace
    RadiaBeam, Marina del Rey
  • W.A. Clemens, J. Henry, F. Marhauser, R.A. Rimmer, A.T. Wu, X. Zhao
    JLAB, Newport News, Virginia
  • O. Harrysson, T. Horn, K. Knowlson, T. Mahale, G. Prasanna
    NCSU, Raleigh, North Carolina
  • F. Medina, R.B. Wicker
    University of Texas El Paso, W.M. Keck Center for 3D Innovation, El Paso, Texas
  • L.E. Murr
    University of Texas at El Paso, El Paso, Texas
 
 

A key issue for high average power, normal conducting radio frequency (NCRF), photoinjectors is efficient structure cooling. To that end, RadiaBeam has been developing the use of Solid Freeform Fabrication (SFF) for the production of NCRF photoinjectors. In this paper we describe the preliminary design of a high gradient, very high duty cycle, photoinjector combining the cooling efficiency only possible through the use of SFF, and the RF efficiency of a re-entrant gun design. Simulations of the RF and thermal-stress performance will be presented, as well as material testing of SFF components.